Breville Barista Touch Stops Brewing After 3 Seconds – 5 Main Reasons and 6 Simple Solutions


breville barista touch stops brewing after 3 seconds
(Earning Disclaimer: As an Amazon Associate, we earn commissions from qualifying purchases at NO additional cost to the customer.)

Breville Barista Touch coffee machine comes with well equipped and innovative touch screen menu.

You can use already programmed coffee menus available on the screen and can make your favorite espresso, latte, Americano, Cappuccino within few minutes.

You will find a built-in coffee grinder which helps you grind all types of coffee grounds within few minutes.

This machine has heating time of just 3 seconds which means it can heat up within just 3 seconds and get ready to brew your favorite coffee quickly.

However, sometimes, this Breville Barista Touch machine abruptly stops brewing after just 3 seconds.

What could be the possible reasons behind this machine not brewing properly.

There are 5 main problems which I am going to discuss in this article in detailed manner.

Don’t worry!

I am also going to provide their solutions as well which you can implement on your own and solve then problem as quick as possible.

The main problems that can affect the brewing capability of your Breville Barista Touch machine are related to the water tank, clogged filters, programming malfunction, use of too much fine ground coffee and internal clogging.

The first reason can be because the water tank is empty.

So, make sure that it is at least half-filled.

Problems in brewing can also be because of the clogged filter.

This can occur especially with double-walled filter cups.

If you have dual wall filters, make sure to double-check.

Another solution can be that you recheck your method.

Try resetting the recording volume by holding the program button for 4 seconds (with the device powered on) and then releasing it.

I will explain more problems and their solutions in this article ahead.

So, I recommend reading this article completely to understand all the issues and their solutions related to the brewing problem of your Breville Barista Touch machine.

Table of Contents

5 Main Reasons That Cause Breville Barista Touch Machine To Stop Brewing After 3 Seconds

Following are the 5 main reasons why Breville Barista Touch machine stops brewing after just 3 seconds.

Reason 1: Empty Water Reservoir

Sometimes, you forget to fill up the water tank fully and this is when your machine can have problems in brewing coffee.

Therefore, make sure the water tank is full before your start brewing process.

At least the tank should be half filled to make sure the machine does not stop brewing after first 3 seconds.

Reason 2: Programming

There can be some problems with programming functions which can cause your machine to strop after your start brewing process.

In this case, you need to press and hold the Program button for 4 seconds (with the unit on) to reset the recording volume and release it.

Reason 3: Clogged Filter Cups

Sometimes, the filter cups get clogged with coffee oil and debris.

This mostly happen with double-walled filter cups.

If no water is coming out when you brew a shot with no coffee in the filter basket, then it can be inferred that filter cups are clogged for sure.

Reason 4: Internal Clogging and Debris Buildup

In some cases, the shower screens get clogged if you don’t have a portafilter installed and no water comes out after resetting the machine.

Please note that the extraction head of the machine should be cleaned regularly to prevent this problem.

Reason 5: Use of Extremely Fine Coffee Grounds

When you use too fine ground coffee in the grinder, then there is obviously a big water flow problem occurs inside the machine.

Water can not pass through properly due to larger resistance by coffee grounds.

This later on causes problem in brewing coffee and your Breville Barista Touch machine can stop brewing after few seconds.

6 Easy Solutions to Fix Brewing Stoppage of Breville Barista Touch After 3 Seconds

Following are some simple methods to fix the abrupt stopping of Breville Barista Touch.

Solution 1: Make Sure Water Tank is Full

As mentioned in the list of reasons above, empty water tank can stop brewing process abruptly for Breville machines.

You can prevent this abrupt brewing stoppage by filling up the water tank to the full or at least to the half level.

Solution 2: Set Right Programming Settings

You can reset the volume for the coffee shots just by clicking and holding the program button for about 4 seconds.

After that you can release the program button to test the water volume.

You can also test the amount of water by extracting directly into a measuring cup without using a portafilter or basket.

One cup should brew about 1.5 ounces of water.  

Your two cups should brew about 2.5 ounces of water.

Solution 3: Get Rid of Clogged Filter Cups

Prepare a shot without coffee in the basket to test the filter basket.

If water does not come out, then the filter basket must be replaced.

If you see that the filter cups are clogged and full of debris, then you need to throw them out and replace them with the new ones.

Use of clogged filter cups often lead to brewing problems in your Breville machine.

You can get new dual wall filter cups for your Breville Barista Touch machine to streamline the brewing process without any issues.

Click Here to Get New Replacement Dual Wall Filter Cups for Breville Barista Touch Machine.

Solution 4: Use Little Coarse Ground Coffee

When you use too fine ground coffee, then it creates lot of hurdles for water to easily pass through the grinder and filters.

After that, it creates problems for coffee brewing.

Therefore, you need to use a coarser grind of coffee to prevent these issues.

You can do that by setting the dial on the left side of the Breville Barista Touch to a higher number.

Finding the right size for your batch of beans may take few attempts to perfect.

Solution 5: Unclog and Clean Your Machine Regularly

To clean the internal limescale and coffee oil buildup in your machine, you need to follow these below mentioned 6 steps.

Step 1: You will see a metal grill on the group head or shower head where you attach a portafilter to make espresso.

Step 2: Switch off your machine and let it cool.

Step 3: Once cool, carefully remove the screws in the center of the grill.

Step 4: Remove the grill and seal the ring.

Step 5: Once these are off, rinse them well under running water.

Step 6: Dry well with a paper towel to remove any residue.

Solution 6: Always Use Fresh and Filtered Water

If you regularly use hard water in your machine, it will accumulate minerals and limescale buildup in the machine’s internal components.

This will reduce brewing temperature and flow, the taste of the shot, and the machine’s power.

Therefore, always use fresh, pure and filtered water to minimize the internal clogging problem of your machine.

Despite using the provided filter, you must carry out your machine’s descaling process.

To do this, open settings and choose ‘Descale cycle.’

The water tank should never be removed or completely emptied during descaling.

Recommended Articles for You:

5 Steps to Solve Water Flow Problems of Breville Barista Express

5 Reasons Why Breville Barista Express’s Steam Wand Does not Work

4 Reasons Why Breville Barista Express Grind Size Does not Work

Find Main Reasons That Cause High, Low and No Pressure in Breville Coffee Machine

3 Simple Steps to Reset Breville Barista Touch Coffee Machine

You can easily reset your Breville Barista Touch machine to factory defaults if you want to overwrite any customizations made to your machine and start over.

A factory reset erases any configuration changes you make earlier, including custom drinks.

Step 1: To do this, tap the gear icon in the upper right corner of the display screen to display the settings menu.

Step 2: Then scroll to Settings & tap Factory reset.

This will give you the option to reset the device.

Step 3: Tap “Reset” and Confirm.

Please note that a factory reset will erase any previously created custom drinks.

5 Steps to Clean and Unclog Breville Barista Touch Coffee Machine

These are the 2 main reasons to keep your Breville Barista coffee machine clean on a regular basis.

The first is that you will get a delicious shot if you brew coffee on a clean machine.

The second reason is that clean machines last for much longer period.

Cleaning and maintenance should cover all sides of the machine, from cleaning the extraction head and steam wand to descaling and regular replacement of the water filter.

As a general rule, for 2-5 cups of coffee a day, some parts need to be cleaned weekly.

But for grinders and water tanks, it only needs to be cleaned every 2-3 weeks.

You can clean and unclog your Breville Barista Touch machine in 5 easy steps.

Step 1: Use coffee cleaning brushes to clean the interior of your machine.

Step 2: To clean the clogged steam wand, let it cool for some time after use and wipe it with a soft cloth.

You can also use a pin cleaning tool to clear the clogged debris in the steam wand.

Step 3: Rinse the filter baskets to remove the coffee oil and other debris collection.

Step 4: Change your water filter every two months to eliminate the germs accumulated over time.

Step 5: Brush any coffee remains from the grinder and clean the oil from the coffee beans.

References:

https://support.breville.com/us/content/barista-touch-bes880/#1597877546847-b73e3377-ce6e

https://coffeeaim.com/how-to-clean-a-breville-espresso-machine/

https://coffeeaffection.com/how-to-clean-a-breville-espresso-machine/

https://www.breville.com/us/en/inspiration/tutorials/the-barista-touch/customising-your-machine/how-to-perform-a-factory-reset

Recent Posts