Is your Philips Saeco Xelsis Espresso Machine displaying the “water circuit priming” message continuously?
If yes, then there may be some issues with your coffee machine for sure.
And if not fixed within time, the problem can be worse later on.
Although Philips Saeco Xelsis comes among the best coffee machine models manufactured by Philips, it’s a simple machine after all.
And every machine has its own pros and cons.
In this article, I will be taking a close look at a very common yet annoying issue with the Philips Saeco Xelsis espresso machine.
In this problem, the machine keeps flashing the “water circuit priming” message without any stop.
First of all, it’s important to know what the term “water circuit priming” means for your espresso machine.
Priming a new coffee machine is quite a common task that you need to do in the first place after bringing an espresso machine home.
In this process, you need to clear an airlock from the water lines of your machine so that it can pull out water easily.
To make sure your machine operates efficiently, you should prime the machine every once in a while.
Now coming back to the topic, there can be several reasons why your Philips Saeco is displaying the water circuit priming message constantly.
One such reason could be that there is an air blockage inside the water lines of your machine.
This happens mainly if your machine is brand new or hasn’t been used for a long time.
Luckily, fixing this issue isn’t very difficult.
All you need to do is clean the water lines and make sure there is no blockage there.
Do this and see if the espresso machine is still displaying the message and if you are still unable to stream water from your machine.
If it does so, then I recommend to know all the possible 4 reasons that cause water circuit priming message and their solutions which I have provided in this article.
Table of Contents
- 4 Reasons That Cause Water Circuit Priming Message on Saeco Xelsis Espresso Machine
- 4 Main Solutions to Fix Problem of Water Circuit Priming on Saeco Xelsis Coffee Machine
Below, I have mentioned a 4 most common reasons why your Philips Saeco Xelsis coffee maker is displaying the water circuit priming message non-stop.
According to the Philips Saeco Xelsis manual, users should prime the coffee machine every time they use it after a long time of gap.
Also, they should do it if they have left the water tank of the machine empty for a long while.
If not, there is a high chance they will see the water circuit priming message being displayed on their machine constantly.
During the warm-up phase of the machine, some people unintentionally keep the steam knob open.
if you have unintentionally, or intentionally, leave the steam knob open, then also Saeco Xelsis machine can display water circuit priming message non-stop.
If your coffee machine’s flow meter is experiencing restrictions in its work, you may have the issue as well.
This problem usually happens if something like a coffee particle gets stuck into the machine’s water receptacle while you were filling the bean hopper and the water tank was off at that time.
If you are using your Philips Saeco Xelsis coffee machine just to steam milk regularly, then there are high chances that the steam nozzle can get clogged.
After that, you have to prime your machine properly.
If not, it will keep displaying the water circuit priming error message until you fix it.
So, these are the 4 main reasons why your Philips Saeco Xelsis espresso machine keeps displaying the water circuit priming message on its digital panel.
In the next section, I will be providing you with the 4 possible solutions for each of the four reasons mentioned here.
Recommended Articles for You:
In the previous section, you read about 4 possible reasons that cause water circuit priming error message on the Saeco Xelsis coffee machine.
And since we have the reasons now, fixing it won’t be so tough.
Below, I have mentioned the best possible solution for each of the 4 four reasons listed in the previous section respectively.
It means that solution 1 here is the fix for reason 1 listed in the previous section and so on.
You should prime your espresso machine if it is brand new or you haven’t used it in a long gap.
Doing this makes sure that there is no air blockage in the water lines of your machine.
After that, you can stream water quite effortlessly from the machine.
Priming the machine is very easy and takes just few minutes of yours.
You just need to follow 4 simple steps mentioned below to do so.
4 Steps to Prime Philips Saeco Xelsis Machine
Step 1: Remove the water tank from the machine and make sure it is full of water.
Also, make sure it is operating properly by pressing the seal on the outlet and checking if water is coming out of it.
Step 2: Replace the water tank properly.
Step 3: Turn the hot water tap on.
Step 4: Now, you will hear the sound of the pump starting and see water spurting from the tap.
After that, you need to wait for a while until the stream is steady and once it is so, turn it off.
And there you go.
Now, you have successfully primed your Philips Saeco coffee machine.
See if the machine is still displaying the water circuit priming message.
If it does so, then move on to the next solution.
The steam knob shouldn’t be on when your machine is in its warm-up phase.
Make sure it remains off during the warm-up phase.
However, if it is left open during the process, then you will have to prime your machine and do not repeat this mistake again.
If there is something like a piece of coffee stuck in your coffee machine’s flow meter intake, then you will obviously need to clean it properly.
Take out the flow meter from the back bottom of your coffee maker where it is attached to the tube that goes to the receptacle.
Then clean the intake from inside.
While executing this process, make sure that the water part should be covered if you are working on the beans part and vice versa.
See if the end of your Philips Saeco Xelsis Machine’s steam nozzle is clogged.
If it is indeed cluttered with coffee oil and other debris, then you need to clean it using a sharp needle carefully.
If the problem still persists, then kindly perform a hot water cycle with the knob and see if that works.
If the problem does not solve even now, then you would need to replace the steam valve of your coffee maker.
So, these are the 4 main solutions that you can try if your Philips Saeco Xelsis keeps displaying the water circuit priming message on its control panel.
I have tried a few of them personally and found them to be effective.
I hope they will solve your problem as well.